-
Features • Magnetic drive pump • Filter chamber with welded bottom (no seal) • PP construction, non-metallic solution contact • EPDM elastomers • Cartridge tightened by knob, no by-pass • Air release valve • Drain valve • Max. temperature 70˚C • Hose connection, in & outlet same diameter • Single phase motor with thermal protection • On/Off switch IP55 and cable included -
Features • Very easy, leak free, in-tank installation • Compact, requires only 0 180 mm space • Easy connection above cover, no outlet pipe required • Including complete +GF+ union end • Free turning shaft, no seal or bearing, can run dry • Self priming when flooded • EPDM elastomers for PP and FPM for PVDF • Including suction strainer • Max. temperature PP 80°C, PVDF 100°C -
Features • Immersion length 300mm • Environmentally safe in-tank installation • Free turning shaft – no seal • Self-priming – can run dry • Full length motor shaft • Suction strainer • Outlet sockets available in PP and CPVC -
Features • Cantilever design, no seal or bearing, can run dry • Extended free turning 316L motor shaft • Self priming when flooded • Open impeller allowing solids up to 6 mm • Temperature up to 130°C • EPDM elastomers • Shaft labyrinth to prevent vapours attacking motor • DIN11851 union connection, for easy loosen and tighten -
Features • Very easy, leak free, in-tank installation • Including complete +GF+ union end • Free turning shaft, no seal or bearing, can run dry • Self priming when flooded • EPDM elastomers for PP and FPM for PVDF • Including suction strainer • Max. temperature PP 80°C, PVDF 100°C -
Features • Machined from, Simona® AlphaPlus'" high performance PP • Very easy, leak free, in-tank installation • Easy connection above cover • Including complete +GF+ union end • Free turning shaft, no seal or bearing, can run dry • Impeller locked (no damage with wrong rotation direction) • Self priming when flooded • EPDM elastomers • Max. temperature 80°C • High quality European, purpose designed electric motor: - 3 phase, 50 Hz, 2900 rpm, IP55, multi voltage - with double layer 2C chemical resistant coating - full length SS shaft with PP protection pipe - suitable for frequency drive control - built-in PTC-thermistor - stainless steel fasteners - CE certified and UL listed -
Features • Machined from, Simona® AlphaPlus'" high performance PP • Very easy, leak free, in-tank installation • Easy connection above cover • Including complete +GF+ union end • Free turning shaft, no seal or bearing, can run dry • Impeller locked (no damage with wrong rotation direction) • Self priming when flooded • EPDM elastomers • Max. temperature 80°C -
Features • Low energy consumption due to high hydraulic efficiency and IE3 class Premium Efficiency Motor • Machined high grade Simona® AlphaPlus™ PP • Elastomers EPDM • Sealless pump, can run dry endlessly • Round mounting plate for easy installation • Including discharge pipe with GF union • Impeller locked (no damage with wrong rotation direction) • Oversized motor according to Hendor heavy duty specifications • Stainless steel shaft and fasteners (no metal in contact with liquid) • Motor 4 pole, IP55, Class F, S1 Duty and PTC-160 • Double layer 2C chemical resistant coating • Hoisting eyes for easy lifting and transportation • CE and usULc certified complying with IEC 60034 standards -
Features- Very easy, leak free, in-tank installation
- Compact, requires only 0 130 mm space
- Easy connection above cover, no outlet pipe required
- Including complete +GF+ union end
- Free turning shaft, no seal or bearing, can run dry
- Self priming when flooded
- EPDM elastomers for PP and FPM for PVDF
- Including suction strainer
- Max. temperature PP 80°C, PVDF 100°C
-
Features • Compact and robust, service friendly • Filter chamber with welded bottom (no seal) • String wound, spunbonded, pleated or carbon cartridge (max. Ø 70mm) • All PP or PVDF construction • Max. temperature PP 80˚C / PVDF 100˚C • Unions for rigid piping (PP, PVDF or CPVC sockets) -
Features • Compact and robust, service friendly • Filter chamber with welded bottom (no seal) • Discs (thin/thick paper, cloth), cartridges (max. Ø 69mm) or pleated bag • All PP construction • Top plate made of glass-filled PP • Max. temperature PP 80˚C • External fasteners in SS316 • Unions for rigid piping (PP or CPVC sockets) -
Features • Compact and robust, service friendly • Filter chamber with welded bottom (no seal) • Cartridges (max. Ø 70mm) • All PP construction • Top plate made of glass-filled PP • Max. temperature PP 80˚C • External fasteners in SS316 • Unions for rigid piping (PP or CPVC sockets) -
Features • Compact and robust, service friendly • Filter chamber with welded bottom (no seal) • Discs (thin/thick paper, cloth), cartridges (max. Ø 70mm) or pleated bag • All PP construction • Top plate made of glass-filled PP • Max. temperature PP 80˚C • External fasteners in SS316 • Unions for rigid piping (PP or CPVC sockets) -
Bag Filtration • Large dirt holding capacity • Easy bag change • Low operating cost Bag Filtration Plus • Bag with PP micro fibres • For use with Oil / grease • Gel like sludge Carbon purification • Carbon granules • Efficient removal of organic impurities -
Features • Compact and robust, service friendly • Filter chamber with welded bottom (no seal) • Discs (thin/thick paper, cloth), cartridges (max. Ø 70mm) or pleated bag • All PP or PVDF construction • Top plate made of glass-filled PP • Max. temperature PP 80˚C / PVDF 100˚C • External fasteners in SS316 • Unions for rigid piping (PP, PVDF or CPVC sockets) -
Why use HRC? • to recover precious metals • to remove metal from waste streams • to reduce (rinsing) water consumption • to avoid troublesome techniques to convert recovered precious metals back to liquids/production -
Features • Magnetic drive • Sealless, 100% leak free • Ceramic bearings • Including complete +GF+ union ends • EPDM elastomers for PP and FPM for PVDF • Max. temperature PP 80°C, PVDF 100°C • Stainless steel fasteners and type shields • Extra strong neodymium magnets • Single stage operation • High quality European, purpose designed electric motor: - 3 phase, 50/60 Hz, 2800/3400 rpm, IP55, multi voltage - with double layer 2C chemical resistant coating - suitable for frequency drive control -
Features • Magnetic drive • Sealless, 100% leak free • Ceramic/PTFE bearings • Including complete +GF+ union ends • EPDM elastomers • Max. temperature PP 80°C, PVDF 100°C • Stainless steel fasteners and type shields • Extra strong neodymium magnets • Single stage operation • High quality European, purpose designed electric motor: - 3 phase, 50/60 Hz, 2900/3500 rpm, IP55, multi voltage - with double layer 2C chemical resistant coating - suitable for frequency drive control -
Features • Magnetic drive • Sealless, 100% leak free • Ceramic/PTFE bearings • Including complete +GF+ union ends • EPDM elastomers • Max. temperature 80°C • Stainless steel fasteners and type shields • Extra strong neodymium magnets • Single stage operation • High quality European, purpose designed electric motor: - 3 phase, 50/60 Hz, 2900/3500 rpm, IP55, multi voltage - with double layer 2C chemical resistant coating - suitable for frequency drive control -
Features • Magnetic drive • Sealless, therefore leakfree • Provide extra safety factor for agressive and expensive liquids • Standard with GF union connetions with a choice of sockets, available in PP, PVDF and CPVC • Max. temp. PP 80˚C / 176˚F , PVDF 100˚C / 212˚F • Motor with two component Polyurethane coating for excellent chemical resistance -
Features • Single mechanical seal • Ceramic seal • Including complete +GF+ union ends • EPDM elastomers • Max. temperature 80°C • Stainless steel fasteners and type shields • Single stage operation • High quality European, purpose designed electric motor: - 3 phase, 50/60 Hz, 2900/3500 rpm, IP55, multi voltage - with double layer 2C chemical resistant coating - suitable for frequency drive control -
Features • Service friendly, ideal cleaning access height • Magnetic drive or mechanical seal pump • Filter chamber with welded bottom (no seal) • DOE cartridges • All PP construction, max. temperature PP 80˚C • Unions for rigid piping (PP, PVDF or CPVC sockets) • Standard with 3 phase motor, thermal overload switch, lead without plug, pressure gauge, air release and drain valve -
Features • Service friendly, ideal cleaning access height • Magnetic drive pump • Filter chamber with welded bottom (no seal) • Discs (thin/thick paper, cloth) or cartridges • All PP construction • Max. temperature PP 80˚C • Bottom-out or top-out model • Choice of slurry tank for carbon treatment, mixing and priming • Unions for rigid piping (PP or CPVC sockets) • Standard with 3 phase motor, thermal overload switch, lead without plug, pressure gauge, air release and drain valve -
Features • Magnetic drive or mechanical seal pump • Filter chamber with welded bottom (no seal) • Machined from Simona® AlphaPlus™ high performance PP • Including complete +GF+ union ends • EPDM elastomers for PP and FPM for PVDF • Max. temperature PP 80°C, PVDF 100°C • Stainless steel fittings, fasteners and type shields • Pressure gauge, air release and drain valve • Thermal overload incl. on/off switch and lead -
Features • Microfibers can be reused • Absorbs 6-8times its own weight • Huge filter surface area and voids volume -
Features • Light weight SS316 filter chamber • Easy to use Vee clamp closure • Max. temperature 110˚C • Max. pressure 10 bar • EPDM O-rings
